How to Connect VVDI BIMTool Pro via USB and DoIP?

The main feature of Xhorse VVDI BIM Tool Pro differs from VVDI BWM is adding an DOIP port connection way to extremely increase coding and programming efficiency. Today vvdishop.com will quickly introduce how the 2 connection ways working.

As you can see, there are 2 connections ports on VVDI BIM tool, the left bigger one is DOIP port, the right one is USB port. How do we connect it?

If your computer has only one USB port, then connecting it via USB. Double click BMW tool software, wait a while for connecting… When the bottom bar is showing “Connect 1 OK”, which means VVDI BIM tool has connected with computer successfully.

If you require to use DOIP port, please notice do not plug the wires into 2 ports at the same time. So let us remove the cable and re-plug it into the DOIP port. The other port should be connected with a car for power on. I am now using a test platform instead, the light is on.

Close BMW tool software to restart again. The bottom bar is showing “Connect 2 OK” with its address, which means connection is succeed.

The speed of programming and download data will be much faster when using DOIP connection. Technicians can even finish to program a single module in 15-20 minutes.

VVDI BIMTool Pro not only allows to perform key programming for locksmith, but also provide maintenance and diagnosis features for car repair shops. All those can be done via USD & DOIP connection ways.

http://blog.vvdishop.com/connect-vvdi-bim-tool-pro-via-usb-doip/

Comments

How to Solve VVDI BIMTool Error 211?

The Xhorse VVDI BIMTool Pro reports error 211 when I was trying to flash an EGS transmission. “Error:211 Error om flash programming Programming state invalid.” Solution: Slow down the communication speed between the vvdi bimtool and the control unit. Go to Option tab- Parameters settings – change programming speed to 1 (it is three by default). Read also: Xhorse VVDI BIMTool Pro Read BMW MSD80 ISN and Change VIN Success

VVDI BIMTool Pro BMW FEM BDC KM Reset Guide

Tutorial: BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using Xhorse VVDI BIMTool Pro . i.e. F20 FEM module Procedure: Remove BMW FEM module from the vehicle Set up bench connection. Connect VVDI BIMTool pro with godiag BMW FEM test platform , FEM module, feed vvdi with 12v+ power supply (very important) Turn on ignition switch of the godiag test platform Run Xhorse vvdi bim tool software , go to BMW/FEN Key Learn and Get key Information As you can see 2 keys are programmed and you can see VIN and current mileage is 183374 KM Press Reset KM BIMTool will ask to program FEM/BDC first Press Program BMW FEM/BDC System Follow 4 steps to program BMW FEM/BDC Step 1. Backup coding Read FEM/BDC coding ia OBDII or on bench Step 2. Prepare service EEPROM Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to...

Xhorse VVDI BIMTool Pro Cannot Test Frequency Solution

Problem: I had a problem with Xhorse VVDI Bimtool Pro when I try to check the frequency of the key but it is in Chinese. I am pressing the “F” button and nothing happens when i try to press key buttons. i Have allready update firmware to 1.8.4 Version but nothing changed. The “T” button for transponder works fine. Solution: Press F, wait 2 seconds press F again followed by an immediate press from the remote, make sure the key is fully flat perpendicular on the blue area. 315Mhz,434Mhz tested fine. To change the Chinese language, double hold both F and T buttons for 5 seconds, it will change the language to English. Same as VVDI2 .

Xhorse VVDI BIM Tool Pro

Search This Blog