2021 Xhorse VVDI BIMTool Pro Unboxing Review

2021 new Xhorse VVDI BIM Tool Pro enhanced edition for BMW is in stock now, this version fixed bugs to keep a stable system than before.

VVDI BIM Tool Pro Package Unboxing Review

Package List:

1pc * VVDI BIMTool Pro Main Unit
1pc * OBD Cable
1pc * Ethernet Cable
1pc * USB Cable
1pc * ECU Reflash Cable
1pc * Plastic Box

VVDI BIMTOOL Outer Box, sturdy and durable, with convenient inter space.

VVDI BIMTool Pro Main Unit, with DOIP port, USB port, OBD port on both sides.

OBD Cable, connect BIMTOOL with car OBD.

Other cables, including Ethernet Cable+ USB Cable + ECU Reflash Cable.

– Ethernet Cable, connect BIMTOOL via DOIP directly, make sure faster network speed during programming.

– USB Cable, connect BIMTOOL via USB, giving another way for computer only has one port.

– ECU Reflash Cable, connect BIMTOOL to do BMW ECU reflash programming.

It may help:

How to connect VVDI BIM Tool Pro via USB & DOIP?

http://blog.vvdishop.com/connect-vvdi-bim-tool-pro-via-usb-doip/

https://www.vvdishop.com/

Comments

How to Solve VVDI BIMTool Error 211?

The Xhorse VVDI BIMTool Pro reports error 211 when I was trying to flash an EGS transmission. “Error:211 Error om flash programming Programming state invalid.” Solution: Slow down the communication speed between the vvdi bimtool and the control unit. Go to Option tab- Parameters settings – change programming speed to 1 (it is three by default). Read also: Xhorse VVDI BIMTool Pro Read BMW MSD80 ISN and Change VIN Success

VVDI BIMTool Pro BMW FEM BDC KM Reset Guide

Tutorial: BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using Xhorse VVDI BIMTool Pro . i.e. F20 FEM module Procedure: Remove BMW FEM module from the vehicle Set up bench connection. Connect VVDI BIMTool pro with godiag BMW FEM test platform , FEM module, feed vvdi with 12v+ power supply (very important) Turn on ignition switch of the godiag test platform Run Xhorse vvdi bim tool software , go to BMW/FEN Key Learn and Get key Information As you can see 2 keys are programmed and you can see VIN and current mileage is 183374 KM Press Reset KM BIMTool will ask to program FEM/BDC first Press Program BMW FEM/BDC System Follow 4 steps to program BMW FEM/BDC Step 1. Backup coding Read FEM/BDC coding ia OBDII or on bench Step 2. Prepare service EEPROM Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to...

Xhorse VVDI BIMTool Pro Cannot Test Frequency Solution

Problem: I had a problem with Xhorse VVDI Bimtool Pro when I try to check the frequency of the key but it is in Chinese. I am pressing the “F” button and nothing happens when i try to press key buttons. i Have allready update firmware to 1.8.4 Version but nothing changed. The “T” button for transponder works fine. Solution: Press F, wait 2 seconds press F again followed by an immediate press from the remote, make sure the key is fully flat perpendicular on the blue area. 315Mhz,434Mhz tested fine. To change the Chinese language, double hold both F and T buttons for 5 seconds, it will change the language to English. Same as VVDI2 .

Xhorse VVDI BIM Tool Pro

Search This Blog