Skip to main content

VVDI BIMTool CAS3 Coding Comfort Access for Remote Control

 Xhorse VVDI BIMTool Pro can do CAS3 coding comfort access to raise the windows with fob’s lock button. Generally, it’s disabled by default. Here I’m going to demonstrate with a BMW E60 on bench.

 

Having all modules been connected:

Dashboard, key, gateway, CAS3 & DME.

VVDI BIMTool CAS3 Coding Comfort Access 1

 

Step1. Firstly insert the key, and turn the ignition on.

VVDI BIMTool CAS3 Coding Comfort Access 2

 

Step2. Open VVDI BIM Tool, click

Exx Program/ Code >> Connect car >> CAS >> Gateway registered unit >> Car access system >> Unit coding >> Read coding

VVDI BIMTool CAS3 Coding Comfort Access 3

VVDI BIMTool CAS3 Coding Comfort Access 4

VVDI BIMTool CAS3 Coding Comfort Access 5

VVDI BIMTool CAS3 Coding Comfort Access 6

Step3. Go to enable options under the folders:

Power windows master >>

Comfort opening with remote control(power window, sunroof or convertible top)

Comfort closing with remote control(power window, sunroof or convertible top)

Comfort opening (power windows, sunroof or convertible top)

Comfort closing(power windows, sunroof or convertible top)

 

Then “Save coding file” when completed.

That’s done.

VVDI BIMTool CAS3 Coding Comfort Access 7

This is how to use VVDI BIMTOOL Pro to enable BMW comfort access to raise the Windows with the fob’s lock button.

www.vvdishop.com

Labels:

Comments

Post a Comment

Popular posts from this blog

How to Solve VVDI BIMTool Error 211?

  The   Xhorse VVDI BIMTool Pro  reports error 211 when I was trying to flash an EGS transmission. “Error:211 Error om flash programming Programming state invalid.” Solution: Slow down the communication speed between the  vvdi bimtool  and the control unit. Go to  Option  tab-  Parameters settings – change programming speed to  1    (it is three by default). Read also: Xhorse VVDI BIMTool Pro Read BMW MSD80 ISN and Change VIN Success
Post a Comment
Read more

VVDI BIMTool Pro BMW FEM BDC KM Reset Guide

  Tutorial:   BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using   Xhorse VVDI BIMTool Pro . i.e. F20 FEM module Procedure: Remove BMW FEM module from the vehicle Set up bench connection. Connect VVDI BIMTool pro with  godiag BMW FEM test platform , FEM module, feed vvdi with 12v+ power supply (very important) Turn on ignition switch of the godiag test platform Run  Xhorse vvdi bim tool software , go to BMW/FEN Key Learn and Get key Information As you can see 2 keys are programmed and you can see VIN and current mileage is  183374 KM Press  Reset KM BIMTool will ask to program FEM/BDC first Press Program BMW FEM/BDC System Follow 4 steps to program BMW FEM/BDC Step 1. Backup coding Read FEM/BDC coding ia OBDII or on bench Step 2. Prepare service EEPROM Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to...
Post a Comment
Read more

Xhorse VVDI BIMTool Pro Cannot Test Frequency Solution

  Problem: I had a problem with  Xhorse VVDI Bimtool Pro  when I try to check the frequency of the key but it is in Chinese. I am pressing the “F” button and nothing happens when i try to press key buttons. i Have allready update firmware to 1.8.4 Version but nothing changed. The “T” button for transponder works fine. Solution: Press F, wait 2 seconds press F again followed by an immediate press from the remote, make sure the key is fully flat perpendicular on the blue area. 315Mhz,434Mhz tested fine. To change the Chinese language, double hold both F and T buttons for 5 seconds, it will change the language to English. Same as  VVDI2 .
Post a Comment
Read more