Skip to main content

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding with Test Platform

 Here one of vvdishop.com’s customers tested BMW FEM/BDC module backup coding using the Xhorse VVDI BIMTool pro and Godiag FEM/BDC test platform.

 

You can do key programming, mileage correction, coding and many more no fuse if use this test platform.

It works very well people did a lot of FEM on it and there was never a problem.

Take out the FEM/BDC module and connect the godiag platform on bench.

 

Connect godiag fem platform with BDC module, the other end connect with VVDI BIM Tool using DB25 adapter that comes with the platform.

Turn on ignition emulator on the platform, the immo indicator turns to red which means communication is well built.

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 1

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 2

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 3

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 4

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 5

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 6

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 7

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 8

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 9

Go to BMW FEM/BDC key learn function

Get key information

and start backup coding.

Then you can program keys to vehicle.

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 10

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 11

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 12

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 13

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 14

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 15

Xhorse VVDI BIMTool BMW FEM BDC Backup Coding 16

www.vvdishop.com

http://blog.vvdishop.com/xhorse-vvdi-bimtool-pro-bmw-fembdc-backup-coding/

Labels:

Comments

Post a Comment

Popular posts from this blog

VVDI BIMTool Pro BMW FEM BDC KM Reset Guide

  Tutorial:   BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using   Xhorse VVDI BIMTool Pro . i.e. F20 FEM module Procedure: Remove BMW FEM module from the vehicle Set up bench connection. Connect VVDI BIMTool pro with  godiag BMW FEM test platform , FEM module, feed vvdi with 12v+ power supply (very important) Turn on ignition switch of the godiag test platform Run  Xhorse vvdi bim tool software , go to BMW/FEN Key Learn and Get key Information As you can see 2 keys are programmed and you can see VIN and current mileage is  183374 KM Press  Reset KM BIMTool will ask to program FEM/BDC first Press Program BMW FEM/BDC System Follow 4 steps to program BMW FEM/BDC Step 1. Backup coding Read FEM/BDC coding ia OBDII or on bench Step 2. Prepare service EEPROM Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to...
Post a Comment
Read more

How to Solve VVDI BIMTool Error 211?

  The   Xhorse VVDI BIMTool Pro  reports error 211 when I was trying to flash an EGS transmission. “Error:211 Error om flash programming Programming state invalid.” Solution: Slow down the communication speed between the  vvdi bimtool  and the control unit. Go to  Option  tab-  Parameters settings – change programming speed to  1    (it is three by default). Read also: Xhorse VVDI BIMTool Pro Read BMW MSD80 ISN and Change VIN Success
Post a Comment
Read more

BMW CAS FEM BDC Coding Lost VVDI BIMTool Pro Solution

This is a tutorial on how to solve BMW CAS/FEM/BDC version & coding loss issue with  Xhorse VVDI BIMTool Pro . You can refer to the solution in this article if you’ve met the following problems:   BMW CAS4+ and FEM/BDC OBD show unsupported versions and require upgrades. BMW CAS4+ and FEM/BDC OBD preprocessing completes but indicates coding loss with no recovery possible. BMW OBD preprocessing is unexpectedly interrupted due to missing SWFL version, halting further processing. The vehicle’s SWFL or coding version mismatch causes functional deficiencies.   Solution Here’s taking FEM module as an example.   When the SWFL, CANFD coding and key position info are missing, we can resolve these issues using BIM TOOL or BIMTool Pro. Connecting Tools Connect  VVDI BIM TOOL , then open software, select Fxx/Gxx Program/Code >> Auto detect >> Connect car Calculating Programming Files Vehicle programming >> 40-FEM[FEM_BODY] >> Calculate Programming...
Post a Comment
Read more