VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost

Customer lost all of the keys, so today I’m about to make a brand new set for 2006 BMW 530xi CAS2 with Xhorse VVDI BIMTool Pro by OBD. Having cut 2 keys via Key Cutting Machine, let’s continue to program keys.

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 2

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 3

Connect VVDI BIM TOOL to OBD via cable.

Open BMW TOOL software,

CAS Key Learn >> Connect >> Get Key Info >> Add key

As I don’t have the working key in ignition, click “OK”.

Save key info data file.

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 4

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 5

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 6

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 7

Put first one key into VVDI BMW TOOL slot.

Prepare dealer key with programmer >> Choose key position to be programmed: Key5 >> Prepare dealer key with programmer

Is the new key have keyless? No

Key make okay and locked. Please use it start the car.

If can not start engine, use “Add Key” function add the dealer key to CAS system.

If key can start engine, but keyless not working, please use “Repair Keyless Key” function.

Go on to program next key.

Choose key6, repeat operation as first key.

Key make okay.

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 8

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 9

Now put the keys into ignition in turn for a test.

Perfect. Both are added into the system. Car can recognize.

Test the remotes, both can work well.

Just make sure remote batteries are not dying.

All done.

VVDI BIMTool Pro Program BMW 530xi CAS2 All Keys Lost 10

This is how to program BMW 530xi CAS2 all keys lost with VVDI BIM Tool Pro successfully.

www.vvdishop.com

Comments

How to Solve VVDI BIMTool Error 211?

The Xhorse VVDI BIMTool Pro reports error 211 when I was trying to flash an EGS transmission. “Error:211 Error om flash programming Programming state invalid.” Solution: Slow down the communication speed between the vvdi bimtool and the control unit. Go to Option tab- Parameters settings – change programming speed to 1 (it is three by default). Read also: Xhorse VVDI BIMTool Pro Read BMW MSD80 ISN and Change VIN Success

VVDI BIMTool Pro BMW FEM BDC KM Reset Guide

Tutorial: BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using Xhorse VVDI BIMTool Pro . i.e. F20 FEM module Procedure: Remove BMW FEM module from the vehicle Set up bench connection. Connect VVDI BIMTool pro with godiag BMW FEM test platform , FEM module, feed vvdi with 12v+ power supply (very important) Turn on ignition switch of the godiag test platform Run Xhorse vvdi bim tool software , go to BMW/FEN Key Learn and Get key Information As you can see 2 keys are programmed and you can see VIN and current mileage is 183374 KM Press Reset KM BIMTool will ask to program FEM/BDC first Press Program BMW FEM/BDC System Follow 4 steps to program BMW FEM/BDC Step 1. Backup coding Read FEM/BDC coding ia OBDII or on bench Step 2. Prepare service EEPROM Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to...

Xhorse VVDI BIMTool Pro Cannot Test Frequency Solution

Problem: I had a problem with Xhorse VVDI Bimtool Pro when I try to check the frequency of the key but it is in Chinese. I am pressing the “F” button and nothing happens when i try to press key buttons. i Have allready update firmware to 1.8.4 Version but nothing changed. The “T” button for transponder works fine. Solution: Press F, wait 2 seconds press F again followed by an immediate press from the remote, make sure the key is fully flat perpendicular on the blue area. 315Mhz,434Mhz tested fine. To change the Chinese language, double hold both F and T buttons for 5 seconds, it will change the language to English. Same as VVDI2 .

Xhorse VVDI BIM Tool Pro

Search This Blog