Skip to main content

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool

 Here is another xhorse vvdi bimtool pro tutorial- BMW E61 Airbag Passenger Seat Occupancy off sensor encoding. The procedure can be applied to  E61 E60 E90 E92 E87 chassis.

VVDI BIMTool is for key, coding and programming. Many function that cgdi bmw does not have.

 

NOTE:

Depending on the diagnostic device used, error 93C1 can be displayed in different formats.

Error code 93C1

Conversion Hexadecimal 93C1

Decimal 37825

OBD code B13C1

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 1

Instruction:

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 2

Connect VVDI BIMTool Pro with vehicle

Run Software, Select Exx Program/Code->Connect Car

Auto detect vehicle information

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 3

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 4

Select CAS-> Module information/DTCs-> Select Airbag module-> Gateway Registered Unit-> Module information/DTCs->Read Unit inforamtion-> Read DTC

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 5

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 6

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 7

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 8

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 9

VVDI BIMTool Pro reads DTC 37825: ACSM/MRS: Communication Fault, Seat occupancy detector, passenger

Google search the fault code, it is the same fault code read by im608

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 10

Select ACSM60 Airbag module, press Unit coding

Read coding
Save Configure File

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 11

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 12

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 13

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 14

Load Configure File

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 15
Select Seat occupancy detection SBE1, Not enabled– and Write coding

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 16

VVDI BIMTool pro coding completed.

No DTC exists.

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 17

IM608 says no fault code detected as well

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 18

Read Configure file and save new configure data

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 19

BMW E61 Airbag Seat Occupancy Sensor Coding with VVDI BIMTool 20

Done.

Labels:

Comments

Post a Comment

Popular posts from this blog

VVDI BIMTool Pro BMW FEM BDC KM Reset Guide

  Tutorial:   BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using   Xhorse VVDI BIMTool Pro . i.e. F20 FEM module Procedure: Remove BMW FEM module from the vehicle Set up bench connection. Connect VVDI BIMTool pro with  godiag BMW FEM test platform , FEM module, feed vvdi with 12v+ power supply (very important) Turn on ignition switch of the godiag test platform Run  Xhorse vvdi bim tool software , go to BMW/FEN Key Learn and Get key Information As you can see 2 keys are programmed and you can see VIN and current mileage is  183374 KM Press  Reset KM BIMTool will ask to program FEM/BDC first Press Program BMW FEM/BDC System Follow 4 steps to program BMW FEM/BDC Step 1. Backup coding Read FEM/BDC coding ia OBDII or on bench Step 2. Prepare service EEPROM Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to...
Post a Comment
Read more

How to Solve VVDI BIMTool Error 211?

  The   Xhorse VVDI BIMTool Pro  reports error 211 when I was trying to flash an EGS transmission. “Error:211 Error om flash programming Programming state invalid.” Solution: Slow down the communication speed between the  vvdi bimtool  and the control unit. Go to  Option  tab-  Parameters settings – change programming speed to  1    (it is three by default). Read also: Xhorse VVDI BIMTool Pro Read BMW MSD80 ISN and Change VIN Success
Post a Comment
Read more

BMW CAS FEM BDC Coding Lost VVDI BIMTool Pro Solution

This is a tutorial on how to solve BMW CAS/FEM/BDC version & coding loss issue with  Xhorse VVDI BIMTool Pro . You can refer to the solution in this article if you’ve met the following problems:   BMW CAS4+ and FEM/BDC OBD show unsupported versions and require upgrades. BMW CAS4+ and FEM/BDC OBD preprocessing completes but indicates coding loss with no recovery possible. BMW OBD preprocessing is unexpectedly interrupted due to missing SWFL version, halting further processing. The vehicle’s SWFL or coding version mismatch causes functional deficiencies.   Solution Here’s taking FEM module as an example.   When the SWFL, CANFD coding and key position info are missing, we can resolve these issues using BIM TOOL or BIMTool Pro. Connecting Tools Connect  VVDI BIM TOOL , then open software, select Fxx/Gxx Program/Code >> Auto detect >> Connect car Calculating Programming Files Vehicle programming >> 40-FEM[FEM_BODY] >> Calculate Programming...
Post a Comment
Read more