VVDI BIMTool Pro Change BMW CAS1-CAS4 KM

Xhorse VVDI BIMTool Pro can change CAS1, CAS2, CAS3, CAS3+, CAS4 (0L15Y), CAS4 (5M48H) KM (mileage) via dump file.

How to Change BMW CAS1-CAS4 KM with VVDI BIMTool Pro?

Change KM for EWS/CAS: Load EEPROM dump, input new KM value, press button Change KM and save new EEPROM dump then write back it to EEPROM.

VVDI BIMTool Pro Change BMW CAS1-CAS4 KM

CAS1/CAS2/CAS3/CAS3+ change KM steps:

1) Record the KM information displayed in instrument, take instrument away from car avoid synchronize KM with CAS automatically

2) Set CAS KM to 0 (you can do this via OBD or EEPROM dump, select correct CAS version)

3) Read instrument EEPROM dump by programmer then save EEPROM dump you read, usually it use M35080 chip

4) Select File Change KM ->M35080 (Instrument) and load EEPROM dump saved in step 3 Attention: this type instrument have 2 algorithm for KM, Algorithm 1 and Algorithm 2， you need try different algorithm to check the Old KM in file value, which one is nearby the KM (write in step 1)), which is the right type. Change new KM with the right type

5) Input new KM

6) Press button “Change KM” and save new EEPROM dump

7) Write new EEPROM dump to M35080 chip

8) Put your instrument in car

9) Finished

Ｆ-Series(CAS4 system) change KM steps:

1) Record the KM information displayed in instrument, take instrument away from car avoid synchronize KM with CAS automatically

2) Set CAS KM to 0km (Change KM with File Change KM, select type accord chip mask, support 1L15Ymask and 5M48H mask)

3) Read instrument EEPROM dump by programmer

4) Select File Change KM ->F-Series Instrument and load EEPROM dump which saved in step 3)

5) Input new KM 6) Press button “Change KM” and save new EEPROM dump

7) Write new EEPROM dump to instrument

8) Put your instrument in car

9) Finished

www.vvdishop.com

Comments

How to Solve VVDI BIMTool Error 211?

The Xhorse VVDI BIMTool Pro reports error 211 when I was trying to flash an EGS transmission. “Error:211 Error om flash programming Programming state invalid.” Solution: Slow down the communication speed between the vvdi bimtool and the control unit. Go to Option tab- Parameters settings – change programming speed to 1 (it is three by default). Read also: Xhorse VVDI BIMTool Pro Read BMW MSD80 ISN and Change VIN Success

VVDI BIMTool Pro BMW FEM BDC KM Reset Guide

Tutorial: BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using Xhorse VVDI BIMTool Pro . i.e. F20 FEM module Procedure: Remove BMW FEM module from the vehicle Set up bench connection. Connect VVDI BIMTool pro with godiag BMW FEM test platform , FEM module, feed vvdi with 12v+ power supply (very important) Turn on ignition switch of the godiag test platform Run Xhorse vvdi bim tool software , go to BMW/FEN Key Learn and Get key Information As you can see 2 keys are programmed and you can see VIN and current mileage is 183374 KM Press Reset KM BIMTool will ask to program FEM/BDC first Press Program BMW FEM/BDC System Follow 4 steps to program BMW FEM/BDC Step 1. Backup coding Read FEM/BDC coding ia OBDII or on bench Step 2. Prepare service EEPROM Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to...

Xhorse VVDI BIMTool Pro Cannot Test Frequency Solution

Problem: I had a problem with Xhorse VVDI Bimtool Pro when I try to check the frequency of the key but it is in Chinese. I am pressing the “F” button and nothing happens when i try to press key buttons. i Have allready update firmware to 1.8.4 Version but nothing changed. The “T” button for transponder works fine. Solution: Press F, wait 2 seconds press F again followed by an immediate press from the remote, make sure the key is fully flat perpendicular on the blue area. 315Mhz,434Mhz tested fine. To change the Chinese language, double hold both F and T buttons for 5 seconds, it will change the language to English. Same as VVDI2 .

Xhorse VVDI BIM Tool Pro

Search This Blog