Skip to main content

Does Xhorse VVDI BIMTool Pro Reset BMW 8HP?

 Does xhorse vvdi bimtool pro support E series 8HP EGS?

 

No, there is no 8HP in E series in the menu.

VVDI BIMTool Pro supports BMW E series 6HP, F series 6HP and F series 8HP.

VVDI BIMTool Pro Reset BMW 8HP

VVDI BIM Tool BMW EGS Function Introduction:

Read gearbox status: Support to read 8HP gearbox status, whether it is a new, etc

Diagram: OBD and gearbox connection diagram

Backup coding: Back up the code in the gearbox

Restore coding: Restore the code in the gearbox

Clear the F-Series 8HP Gearbox ISN: Clear the internal information that have used which have been matched and make them to new part

Reset F-8HP adaptation: Restore the adaptation information in the gearbox to the initial status

Reset F-6HP EWS: Restore the immo information in the gearbox to the initial status

Read E-6HP ISN (E70, E65 and E63): Read the ISN information from the gearbox, it is possible to get several ISN values, but only one is correct. The ISN you get is 4 bytes, the first 2 bytes are the gearbox ISN, and the last 2 bytes are the DME ISN. The gearbox byte is encrypted, and the DME byte is not encrypted. If the ISN read from DME is same as last 2 bytes ISN read from gearbox, it is the correct ISN

Reset E-6HP EWS: Restore the IMMO data in the gearbox to the initial status

Reset E-6HP adaptation: Restore the adaptation information in the gearbox to the initial state

Labels:

Comments

Post a Comment

Popular posts from this blog

VVDI BIMTool Pro BMW FEM BDC KM Reset Guide

  Tutorial:   BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using   Xhorse VVDI BIMTool Pro . i.e. F20 FEM module Procedure: Remove BMW FEM module from the vehicle Set up bench connection. Connect VVDI BIMTool pro with  godiag BMW FEM test platform , FEM module, feed vvdi with 12v+ power supply (very important) Turn on ignition switch of the godiag test platform Run  Xhorse vvdi bim tool software , go to BMW/FEN Key Learn and Get key Information As you can see 2 keys are programmed and you can see VIN and current mileage is  183374 KM Press  Reset KM BIMTool will ask to program FEM/BDC first Press Program BMW FEM/BDC System Follow 4 steps to program BMW FEM/BDC Step 1. Backup coding Read FEM/BDC coding ia OBDII or on bench Step 2. Prepare service EEPROM Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to...
Post a Comment
Read more

How to Solve VVDI BIMTool Error 211?

  The   Xhorse VVDI BIMTool Pro  reports error 211 when I was trying to flash an EGS transmission. “Error:211 Error om flash programming Programming state invalid.” Solution: Slow down the communication speed between the  vvdi bimtool  and the control unit. Go to  Option  tab-  Parameters settings – change programming speed to  1    (it is three by default). Read also: Xhorse VVDI BIMTool Pro Read BMW MSD80 ISN and Change VIN Success
Post a Comment
Read more

BMW CAS FEM BDC Coding Lost VVDI BIMTool Pro Solution

This is a tutorial on how to solve BMW CAS/FEM/BDC version & coding loss issue with  Xhorse VVDI BIMTool Pro . You can refer to the solution in this article if you’ve met the following problems:   BMW CAS4+ and FEM/BDC OBD show unsupported versions and require upgrades. BMW CAS4+ and FEM/BDC OBD preprocessing completes but indicates coding loss with no recovery possible. BMW OBD preprocessing is unexpectedly interrupted due to missing SWFL version, halting further processing. The vehicle’s SWFL or coding version mismatch causes functional deficiencies.   Solution Here’s taking FEM module as an example.   When the SWFL, CANFD coding and key position info are missing, we can resolve these issues using BIM TOOL or BIMTool Pro. Connecting Tools Connect  VVDI BIM TOOL , then open software, select Fxx/Gxx Program/Code >> Auto detect >> Connect car Calculating Programming Files Vehicle programming >> 40-FEM[FEM_BODY] >> Calculate Programming...
Post a Comment
Read more