Skip to main content

Xhorse VVDI BIMTool Pro Cannot Read BMW EWS3 EEPROM Solution

 Problem:

I failed to read BMW EWS3 eeprom using the xhorse vvdi bimtool pro and CAS plug. Error reading data failed. Any solution?

VVDI BIMTool Pro Cannot Read BMW EWS3 EEPROM 1

VVDI BIMTool Pro Cannot Read BMW EWS3 EEPROM 2

VVDI BIMTool Pro Cannot Read BMW EWS3 EEPROM 3

VVDI BIMTool Pro Cannot Read BMW EWS3 EEPROM 4

Solution:

Double check wiring.

Make sure you have CAS Plug Line 4 (shown image below) well connected. Then try again.

VVDI BIMTool Pro Cannot Read BMW EWS3 EEPROM 5

Labels:

Comments

Post a Comment

Popular posts from this blog

Xhorse VVDI BIMTool Pro Update to V1.8.8

  Xhorse VVDI BIMTool Pro   software update to V1.8.8 on June 15th, 2023.   2023-06-15 Require firmware V1.8.4 ===== BMW V1.8.8 ===== 1. Improvement the internet connection 2. Bugfix Free download VVDI BIMTool software V1.8.8 http://dl.xhorse.com/product/bmwtool/software/BMWTOOL-InstallerV188.exe
Post a Comment
Read more

Does Xhorse VVDI BIMTool Pro Reset BMW 8HP?

  Does   xhorse vvdi bimtool pro   support E series 8HP EGS?   No, there is no 8HP in E series in the menu. VVDI BIMTool Pro supports BMW E series 6HP, F series 6HP and F series 8HP. VVDI BIM Tool  BMW EGS Function Introduction: Read gearbox status:  Support to read 8HP gearbox status, whether it is a new, etc Diagram:  OBD and gearbox connection diagram Backup coding:  Back up the code in the gearbox Restore coding:  Restore the code in the gearbox Clear the F-Series 8HP Gearbox ISN : Clear the internal information that have used which have been matched and make them to new part Reset F-8HP adaptation:  Restore the adaptation information in the gearbox to the initial status Reset F-6HP EWS:  Restore the immo information in the gearbox to the initial status Read E-6HP ISN (E70, E65 and E63):  Read the ISN information from the gearbox, it is possible to get several ISN values, but only one is correct. The ISN you get is 4 b...
Post a Comment
Read more

VVDI BIM Tool Pro E F G Series Coding Guide

  This article aims to intro the VVDI BIMTOOL Pro tool’s new function: BMW E/F/G programming and coding BMW E/F/G programming and coding is the most important new feature of  Xhorse VVDI BIM Tool Pro Tool .The ethernet interface will speed up the writing data instead of the USB cable previously used to connect to the BMW Tool. Part 1. Program / Code BMW Exx Connect Car   Can auto detect vehicle model, read module information, support chassis: E36, E38, E39, E46, E52, E53, E60, E63, E64, E65, E66, E67, E70, E71, E72, E83, E85, E86, E89, E90, E91, E92, E93, K1X, K24, KH2, R50, R52, R53, R55, R56, R57, RR1,.etc chassis   Read and write Vehicle configuration(FA/FP) Can read the configuration information inside of vehicle module, and to change the vehicle configuration information for replacing second-hand module.   Registered unit information from gateway / Calculate adaptive control unit Read registered unit information from gateway Calculate adaptive control unit-...
Post a Comment
Read more